This site uses cookies. By continuing, your consent is assumed. Learn more

122.8fm shares

Bare chap takes latin load

opinion

The expansion module is used for the operator panel to communicate via CAN J The correct driver must be installed in the operator panel.

The expansion module is used for the operator panel to communicate via MPI. All configuration of the extended function keyboard is made with E-Designer, version 7. It is assumed that the reader of this manual is familiar with the Eseries concept. English manual MA x: German manual MA x: In easy-to-follow steps, a new project is created. Should the installation space limit the possibility to plug in the adapter directly on the back of the operator panel, simply use the optional bracket and connector cable to mount the adapter in a more convenient location up to 1.

See drawing K k. Complete adaptor plate for E Bare chap takes latin load E mounting hole Complete adaptor plate for E i E mounting hole PDF Resurser The cable you need is a cab 30, you find the drawing attached.

Resurser Is it possible to use an USB mouse on keypad panels? Yes you can Bare chap takes latin load a mouse to keypad panels and you can select object with it, but you cannot manouver objects using the mouse, this still needs to be done using the keypad.

Resurser According to the manual the flash memory should support at least Erase Cycles per Block. Normally this figure tends to increase because these kinds of tests takes very long time to perform. Batteriet driver realtidsklockan i terminalen, denna behövs bla för tidsstämpling av larm och trender.

Skulle batterinivån vara för låg eller helt slut kommer ett felmeddelande "No battery power" att dyka upp på bilden i mitten av terminalen när den bootas om.

Registration

Detta meddelande försvinner dock snabbt, efter ca en sekund. Livslängden på ett batteri är Bare chap takes latin load år om terminalen ligger spänningslös. Projektet i terminalen kommer inte att påverkas av att batterinivån är för låg, projektet sparas i terminalens flashminne och ligger därmed lagrad trots att batteriet är slut.

Vill man ha ett meddelande som varnar för låg batterinivå innan batteriet är helt slut går det att lösa med ett systemkommando på kommandoraden.

När spänningen på batteriet kommer under 2,7 V kommer biten som har angivits efter LOB kommandot, i exemplet nedan M0 att bli ettställd. Denna signal kan användas för att skapa ett meddelande i terminalen som talar om för operatören att det är dags att byta batteri.

Beskrivning över hur ett batteribyte görs finns steg för steg beskrivet i Service and maintenance manualen MA E devices with Batch -xxx or later have rechargeable battery. Batch 10 stands for 12 stands for December.

Hos Chilli finner du Paviljonger...

Newer E terminals with 6-digit numbers Bare chap takes latin load Batch xxx have rechargeable battery. The Service Menu is accessed by setting the mode switches on the operator panel in mode Please see Bare chap takes latin load Hardware and Installation manual for the operator panel for information about the mode switches.

The following options are available in the Service Menu: Load Project from Memory Card An empty operator panel can be started with an existing E-Designer project, used in another panel. The project first has to be saved to a Compact Flash memory card or USB memory stick via the function Save project to memory card for example via a function key.

Insert the memory card in the empty panel before boot-up. Then select Load project from memory card in the service menu and follow the instructions.

Not available for E and E The system program can also be updated via the configuration tool for the operator panels. Calibrate Touch Screen Follow the instructions on the screen to calibrate the touch screen.

The output from the export is a datfile. The file structure is automatically created when formatting the card in the operator panel.

gärna "med lärde män på...

If no operator panel is available, the library structure must be created manually. A function or touch key can be configured in the configuration tool to download the operator panel project, by selecting the function Loads project from memory card. See also chapter Function Keys. The command MCI can be used to indicate that a memory card is used in the panel. Yes, it is possible to load a project to a new terminal with a USB memory is you have saved the project as a.

News feed